Extreme Networks BlackDiamond 12804 User Manual Page 111
- Page / 160
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Installing or Removing an External Compact Flash Memory Card
BlackDiamond 12800 Series Switches Hardware Installation Guide
111
Installing or Removing an External Compact Flash
Memory Card
You do not need to power off the system or remove the MSM from the chassis to install or remove an
external compact flash memory card.
You need an ESD-preventive wrist strap to install a compact flash memory card.
To install the memory card:
1 Attach the ESD-preventive wrist strap to your wrist and connect the metal end to the ground
receptacle on the chassis front panel.
2 Locate the compact flash slot on the MSM, as shown in Figure 72.
Figure 72: Typical Compact Flash Slot Location
3 Hold the memory card between your thumb and forefinger, with the ridge facing toward the bottom
of the chassis.
4 Slide the card into the compact flash slot until you feel resistance.; a portion of the card will
protrude from the slot.
5 Carefully push the card until it is seated into the slot. The card should be fully inserted, or seated,
inside the slot.
6 To verify that the card is fully seated, use the
show memorycard command.
To remove the external compact flash memory card:
1 Use the
eject memorycard command to ensure that you will not lose any data when you remove
the card.
After you use the
eject memorycard command, you can physically remove the card from the
external compact flash slot on the MSM. For more information about the
eject memorycard
command, see the ExtremeXOS 12.0 Concepts Guide.
2 Attach the ESD-preventive wrist strap to your wrist and connect the metal end of the strap to the
ground receptacle on the chassis front panel.
3 Locate the black release pin just above the compact flash slot.
4 Press the release pin until the card releases from the slot.
The card releases to an intermediate position; the card remains partially inserted but is no longer
seated in the slot.
5 Remove the card completely and place it in a safe location.
EX_183
Module status
LEDs
ERR
ENV
SYS Reset
MSTR
Compact
flash
Console
port
MGMT port
- Hardware Installation Guide 1
- Table of Contents 3
- Part 4: Appendixes 6
- Introduction 9
- Conventions 9
- Related Publications 10
- ● Software User Guides 11
- ● Hardware User Guides 11
- Switches 15
- Management Ports 16
- Software Requirements 20
- MSM LEDs 21
- Figure 5: MSM-5 Module 22
- Figure 6: .MSM-5R Module 22
- Figure 7: .MSM-6R Module 22
- I/O Module LEDs 24
- Port LEDs on I/O Modules 24
- GM-20T I/O Module 25
- XM-2X and XM-2XR I/O Modules 26
- XM-2X and XM-2XR LEDs 27
- XM-2HR I/O Module 28
- BlackDiamond Switches 29
- Figure 14: 1200 W DC PSU 30
- Minimum Software Required 31
- Specifications 34
- WARNING! 38
- 4 Site Preparation 41
- Meeting Site Requirements 42
- Wiring Closet Considerations 43
- Temperature 43
- Humidity 44
- Airflow Requirements 44
- Electrostatic Discharge 45
- Securing the Rack 47
- Cabling Standards 48
- Installing Cable 49
- Fiber Optic Cable 50
- Cable Distances 51
- RJ-45 Connector Jackets 52
- Meeting Power Requirements 53
- AC Power Cable Requirements 54
- Applicable Industry Standards 55
- Power cord retaining bracket 58
- 19-inch helper bracket 58
- 5 Unwrap the chassis 59
- Mid-mount 62
- Second mid-mount location 62
- Extreme Networks, Inc 65
- Required Tools and Equipment 66
- Screws (x4) 68
- Grounding point 69
- PSU / fan 69
- Initial Management Access 70
- Logging In for the First Time 71
- Installing the DC Wiring 75
- Squeeze catch 79
- Front Panel LEDs 80
- 325W DC PSU 91
- Torino DC PSU_01A 92
- Torino DC PSU_02A 92
- Torino DC PSU_03A 93
- 325W AC PSU 95
- Torino AC PSU_01 96
- Torino AC PSU_02 97
- Torino AC PSU_07 97
- Torino AC PSU_09 98
- Torino AC PSU_08 98
- Power Supply Cords 100
- Module Slot Assignments 101
- ● ESD-preventive wrist strap 102
- ● #2 Phillips screwdriver 102
- Installing a Backup MSM 105
- Figure 67: Unlocking a Module 107
- Removing a Blank Front Panel 109
- Memory Card 111
- Components 115
- Controllers 116
- Controller 117
- Pre-installation Requirements 118
- Pre-Installation Requirements 119
- Fan tray 120
- Safety Information 125
- Clip lock 127
- Squeeze prongs 127
- BlackDiamond 129
- 12802 switch 129
- 4 Appendixes 131
- A Safety Information 133
- Installing Power Supply Units 134
- Maintenance Safety 135
- General Safety Precautions 135
- Cable Routing for LAN Systems 136
- PoE Devices 136
- Selecting Power Supply Cords 136
- Sicherheitshinweise 140
- Installation von Netzteilen 141
- Wartungssicherheit 142
- Auswahl der Stromkabel 143
- Laserprodukt der Klasse 1 145
- Niederspannungsgeräte 145
- B Technical Specifications 147
- Technical Specifications 148
- BlackDiamond 12802 Switch 149
- Connector Pinouts 153
- Numerics 155
Related products and manuals for Network switches Extreme Networks BlackDiamond 12804
(9 pages)© 2020, manymanuals.com. All rights reserved. | 0.163 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals